Gaylordsville, CT Farm And Equipment Roofs
As a Gaylordsville metal roof coating contractor, we reseal screw rows, prime rust, and coat the steel over pole barns, machine sheds, and equipment buildings.
Long Panel Runs
A typical Gaylordsville metal roof coating job covers a barn or machine shed with panels running eave to ridge in one long sheet. Those long runs move more with heat and cold, so the screws along each purlin loosen first.
We tighten or upsize every fastener, seal the side laps, and close off rust at the open eaves before a single coat goes on the field.
Farm buildings and equipment sheds wear in their own pattern. Here is what we find on them and why it matters before coating.
Coating an equipment building keeps the steel you already own working and puts a fresh skin over the screw rows.
Each fastener head on the long runs ends up wrapped in coating.
Primer over surface rust slows the spread before panels thin out.
Tractors and equipment keep moving in and out while we work overhead.
Reflective white finishes cut the heat soaking through bare steel in summer.
Sealed laps keep wind-driven rain from tracking sideways under the panels.
Old panels stay on the purlins, so nothing goes to a dumpster.
Down the road, another coat can go over this one after a cleaning.
Machinery, feed, and tools under the roof stay out of the drips.
Equipment buildings and barns call for different systems. Panel profile, insulation, and how the space is used point to the right one.
Our standard choice for pole barns and machine sheds with exposed screws. Fasteners and laps are sealed, rust is primed, and an elastomeric coat goes over the full panel run.
Commercial metal roof coating
Good for low-slope equipment buildings where water lingers along the eave or behind a lean-to tie-in. Plan on silicone again whenever the roof needs another coat.
Silicone roof coating
Works well on steeper barn roofs that shed rain quickly. It reflects sun, cleans up with water, and goes on during warm, dry months when panels stay above the maker's temperature limit.
Acrylic roof coating
Insulates bare steel and helps with sweating panels over shops that get heated in winter. A protective coat goes over the foam once it is sprayed to thickness.
Spray foam roofing
For farm offices or retail stands with shingle sections attached to a metal building. Shingles must lie flat and keep their granules; curled ones are replaced before coating.
Shingle roof coatingDrips on stored machinery come from a loose screw, an open lap, or condensation on bare steel. Tell us when they show up and we will find which one it is.
Get A Free Ballpark EstimateHave These Ready
Five steps carry a barn or equipment building from first walk to a finished coat.
We walk the full panel length, count backed-out screws per row, look under the eaves for rust, and check inside for drip marks to separate condensation from real leaks.
Loose screws get tightened, stripped ones come out for larger replacements with fresh washers, and stitch screws go into any side lap that has spread along the panel run.
Panels are pressure-washed to remove dirt, bird droppings, and chalky old paint. Rust at the eaves and around screw heads gets wire-brushed down and then primed.
Seam sealant goes on laps and screw heads first. Base and finish coats then cover each run from eave to ridge, with extra thickness at the panel ends.
Readings are taken along every run and at the eaves, and thin spots get another pass so the cured coat meets the manufacturer's mil spec.
Beyond Gaylordsville, we coat commercial and farm metal roofs in these nearby towns.
Questions from owners of barns, machine sheds, and steel equipment buildings in Gaylordsville.
Most Asked
Expect about $2.50 to $4.00 per square foot of roof area for coating, against roughly $5 to $8 per square foot to replace the panels. Where a barn lands in that range comes down to how many screws need replacing, how much rust sits at the eaves, and how easy the roof is to reach with a lift.
If drips show up on cold, clear mornings with no rain, condensation is the likely cause. Bare steel over an unheated space sweats when warm air meets the chilled panel. Leaks follow rain and line up with a screw row or lap. Coating seals leaks; sweating calls for insulation such as spray foam or better ventilation.
We coat pole barns, machine sheds, and steel equipment buildings in Gaylordsville and the surrounding towns. Call or request an estimate, and we will walk the roof, count loose fasteners, and check the eaves and laps before giving a price for the work.
Yes. Farm operations, landscapers, contractors, and other businesses use these buildings every day, so we coat in sections and keep the main equipment doors clear. Vehicles parked near the walls get covered, and we stop spraying when wind picks up to keep overspray off machinery.
Coating alone holds them for a while, so we fix the screws first. Long panels expand more, which loosens fasteners over the years. We reset tight screws, upsize stripped holes, and replace failed washers. Coating then wraps each head and helps keep water out of the hole.
Open eaves get cleaned, primed, and coated along the panel ends, which is where rust starts on most equipment buildings. If wind has lifted a panel end, we refasten it first. Owners who want the eave closed off can add closure strips before the coating goes on.
Yes, as long as the rust sits on the surface and the steel underneath is solid. We wire-brush the scale and prime it. Panels that have rusted into holes get patched or replaced in that section, and the coating then covers the repaired run along with the rest.
Send us the barn or shed size and where the drips show up, and we will set a time to walk your Gaylordsville roof.